XTOOL
ATOMSTACK
SCULPFUN
ORTUR
TWOTREES
Diode Laser Machines
Laser Modules
Laser Machine Accessories
P Series
S Series
F Series
M Series
Apparel Printer
MetalFab
xTool SafetyProâ„¢ AP2 Air Purifier
Rotary Roller
Honeycomb
Extension Kits
Towers Support Shelf Block
iCube Series
SCULPFUN S10
SCULPFUN S9
Gantry Carts Kits
Wheels
Showing all 11 resultsSorted by popularity
End Stop Switch – PCB Mounted with Connectors and Wire
In stock
₹99.00 Incl.GST / ₹83.90 Excl.GST• Wire type: 22AWG
• Working voltage: 300V
• Working Current: 2A
• Temperature resistance: 80° C
• Cable length: 70cm
4 Core Shielded Xtension Cable 22AWG 2.5 meters
In stock
₹825.00 Incl.GST / ₹699.15 Excl.GST• This Stepper Cable is a terminated at one end with a JST-SM 4 Pin Female connector (standard for our NEMA23 Stepper Motors and our High Torque NEMA23 Stepper Motors) and the other end stripped and tinned for easy termination.
Inductive Proximity Sensor – LJ12A3-4-Z/BX NPN DC6-36V 4mm Normally Open Proximity Switch
In stock
₹427.00 Incl.GST / ₹361.86 Excl.GST• Red LED checks the state of the proximity sensor
• High repeated positioning accuracy
• High switching frequency
• Wide voltage range
• Outer (Thread) Diameter: M12
• Antivibration, dust, water, and oil prevention
• Reverse power protection, short circuit protection, directly connecting with PLC
• Can replace small switches and limit switches
GRBL Based CNC Controller Bundle without UNO R3 CNC Shield Power Supply 24V 350W
In stock
₹8,069.00 Incl.GST / ₹6,838.14 Excl.GST• The DCcduino Uno is a micro-controller board based on the ATmega328 and compatible with the Arduino Uno R3.
Cable for Stepper Motor – DuPont 4p to JST-PH 6p
In stock
₹109.00 Incl.GST / ₹92.37 Excl.GSTThis is a set of great connector cables used for Nema16 or Nema17 stepper motors.
These connector cables are made of premium PVC material for durable and long-lasting use.
Cable is about 1 meter long and it is easy to use and connect.
The precise design will ensure its practicability in the work with highly performance.
AT-09 Bluetooth 4.0 UART Transceiver Module CC2541 Compatible with HM-10
In stock
₹280.00 Incl.GST / ₹237.29 Excl.GSTUltra-low standby power consumption 90uA~400uA
Range up to 60 meters
Built-in PCB antenna
Power input : 3.6v to 6v DC (6v MAX)
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
In stock
₹280.00 Incl.GST / ₹237.29 Excl.GST• Latest Arduino CNC Shield Version 3.10
• GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
• Coolant enable
• Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
• Compact design.
• 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
• 2 x End stops for each axis (6 in total)
Thermistor 100k NTC with 1 Meter Cable Temperature Sensor No connector
In stock
₹100.00 Incl.GST / ₹84.75 Excl.GST High accuracy: ±1%
Resistance value at 25°C=100K
 Wiring insulation: high temperature teflon/PTFE
Wiring length: 1 meter
Operating temperature range: -40 ° C … + 300 ° C
 Dissipation power factor: ≥ 5MW / ° C (static air)
Rated power: 45MW
Thermal time constant ≤ 7S (static air)
Temperature Coefficient of Resistance; -2-5% / ° C
100K NTC 3950 Thermistors Thermal Sensors with dupont Cable for 3D Printer
In stock
₹140.00 Incl.GST / ₹118.64 Excl.GSTHigh accuracy: ±1%
Resistance value at 25°C=100K
Wiring insulation: high temperature teflon/PTFE
Wiring length: 1 meter
Operating temperature range: -40 ° C … + 300 ° C
 Dissipation power factor: ≥ 5MW / ° C (static air)
Rated power: 45MW
Thermal time constant ≤ 7S (static air)
Temperature Coefficient of Resistance; -2-5% / ° C
TTL FTDI Transmitter USB For 3.3V/5V Dual power FT232RL MWC Programmer
In stock
₹180.00 Incl.GST / ₹152.54 Excl.GSTUSBÂ Connector type: USB-Mini
Chip Used:Â FT232RL
Output Voltage 5v and 3.3v Indicator LEDs USB Connector
Automatic detection of data transfer speeds up to 1Mbps
Data exchange capability with an external interface with UART protocol
Supports Windows 8, Windows 7,  Windows Vista, Windows XP, Linux, Mac OS X, Windows CE 4.2-5.2, Windows CE 6.0
TTP224 4-way Capacitive Touch Switch Sensor Module
In stock
₹69.00 Incl.GST / ₹58.47 Excl.GSTOnboard TTP224 capacitive touch sensor IC 4 keys
4 board-level status indicator
Working voltage: 2.4V-5.5V
Advanced Pins breakout, so that the output mode and working mode selectable.
Low power selection
