Filter Replacement Kit for xTool Smoke Purifier (1 Pack)

The Filter Replacement Kit for xTool Smoke Purifier (1 Pack) is a replacement filter set designed to maintain the filtration performance of a compatible xTool Smoke Purifier. xTool specifies that the kit contains 2 pre-filters, 1 middle filter, and 1 main filter, providing replacement components for the purifier’s multi-stage filtration system.

This xTool Smoke Purifier filter replacement kit is intended for users who need to replace filters after extended use. Regular filter maintenance helps maintain effective smoke and dust purification and supports proper purifier performance.

Key Features

• Complete filter replacement kit for the xTool Smoke Purifier
• Includes 2 pre-filters
• Includes 1 middle filter
• Includes 1 main filter
• Designed to maintain the purifier’s filtration performance
• Pre-filter captures visible smoke and dust
• Middle filter filters harmful particles
• Main filter uses activated carbon to address harmful gases and unpleasant odors

Complete Multi-Stage Filter Replacement

The Filter Replacement Kit for xTool Smoke Purifier provides the main replacement filter components in one pack. According to xTool, the package includes two pre-filters, one middle filter, and one main filter.

Replacing the filters as needed helps keep the Smoke Purifier operating with an appropriate filtration setup. Filter condition can change depending on usage, smoke generation, dust levels, and the materials being processed.

Pre-Filter

The included pre-filter is designed to capture visible smoke and dust before the air reaches the subsequent filtration stages. xTool recommends replacing the pre-filter when more than 70% of its surface is covered by dust that cannot be removed.

xTool also explains that the pre-filter can be cleaned for reuse. However, filtration efficiency may decrease after repeated cleaning, so replacement is recommended when filtration performance becomes unsatisfactory.

Middle Filter

The middle filter is part of the Smoke Purifier’s multi-stage filtration system. xTool states that this filter can filter harmful particles down to 0.3 μm with a 99.97% purification rate.

xTool recommends replacing the relevant filter when it can no longer provide satisfactory filtration performance.

Main Filter

The main filter uses premium activated carbon to absorb and remove harmful gases and unpleasant odors. This stage provides an additional filtration layer after the pre-filter and middle filter.

The main filter should be replaced according to its condition and the purifier’s performance rather than being treated as a permanently reusable component.

Filter Maintenance

Regular maintenance is important for the xTool Smoke Purifier filter replacement kit and the purifier itself. xTool recommends monitoring the condition of each filter and replacing filters when their filtration performance or physical condition indicates that replacement is necessary.

For the pre-filter, xTool provides cleaning instructions using clean water without detergent. The filter should be gently hand-washed and allowed to dry completely before being reinstalled.

Replacement Timing

xTool provides the following general maintenance guidance:

These are xTool’s published maintenance recommendations and actual replacement needs can vary with usage conditions.

Compatibility

The current official xTool product information states that the Filter Replacement Kit for xTool Smoke Purifier is compatible with the xTool Smoke Purifier except for xTool F1.

Importantly, xTool notes that the pre-filter in the current listing is only compatible with the 1st Generation Smoke Purifier, which has been discontinued, and is not compatible with Desktop Air Purifier, AP2, or AP2 Max.

Always verify the purifier generation and model before ordering replacement filters.

What’s Included

The xTool Smoke Purifier filter replacement kit contains:

The package contents are based on xTool’s official product information.

Practical Applications

The Filter Replacement Kit for xTool Smoke Purifier is useful for:

• Routine Smoke Purifier maintenance
• Replacing used filtration components
• Maintaining smoke and dust filtration
• Replacing a worn pre-filter
• Replacing the middle filtration stage
• Replacing the activated-carbon main filter
• Keeping replacement filters available for regular laser-processing use

Specifications

Important Compatibility Note

This product should not be confused with filters for xTool’s newer air-purification systems. xTool specifically states that the pre-filter associated with this kit is for the 1st Generation Smoke Purifier and is not compatible with the Desktop Air Purifier, AP2, or AP2 Max.

Check your purifier model before purchasing to ensure that this replacement kit matches your equipment.

Why Choose the Filter Replacement Kit for xTool Smoke Purifier?

For compatible xTool Smoke Purifier owners, the Filter Replacement Kit for xTool Smoke Purifier provides the key filter components needed for ongoing maintenance in one pack. With two pre-filters, one middle filter, and one main filter, it provides a convenient replacement set for maintaining the purifier’s multi-stage filtration system.

Keeping the correct xTool Smoke Purifier replacement filter available can help simplify routine maintenance and ensure that worn filtration components can be replaced when required.